- 您现在的位置：买卖IC网 > Sheet目录510 > SI4737-C-EVB (Silicon Laboratories Inc)BOARD EVAL SI4737 VERSION C
Si4736/37/38/39-C40
5.7. Stereo Audio Processing
The output of the FM demodulator is a stereo
multiplexed (MPX) signal. The MPX standard was
developed in 1961, and is used worldwide. Today's
MPX signal format consists of left + right (L+R) audio,
left – right (L–R) audio, a 19 kHz pilot tone, and
RDS/RBDS data as shown in Figure 13 below.
5.9. Stereo DAC
High-fidelity stereo digital-to-analog converters (DACs)
drive analog audio signals onto the LOUT and ROUT
pins. The audio output may be muted. Volume is
adjusted digitally with the RX_VOLUME property.
5.10. Soft Mute
The soft mute feature is available to attenuate the audio
outputs and minimize audible noise in very weak signal
conditions. The softmute attenuation level is adjustable
Mono Audio
Left + Right
Stereo
Pilot
Stereo Audio
Left - Right
RDS/
RBDS
using the FM_SOFT_MUTE_MAX_ATTENUATION and
AM_SOFT_MUTE_MAX_ATTENUATION properties.
5.11. RDS/RBDS Processor
(Si4737/39 Only)
The Si4737/39 implements an RDS/RBDS* processor
0
15 19 23
38
53
57
for symbol decoding, block synchronization, error
Frequency (kHz)
Figure 13. MPX Signal Spectrum
5.7.1. Stereo Decoder
The Si4736/37/38/39's integrated stereo decoder
automatically decodes the MPX signal using DSP
techniques. The 0 to 15 kHz (L+R) signal is the mono
output of the FM tuner. Stereo is generated from the
(L+R), (L–R), and a 19 kHz pilot tone. The pilot tone is
used as a reference to recover the (L–R) signal. Output
left and right channels are obtained by adding and
subtracting the (L+R) and (L–R) signals respectively.
The Si4731 uses frequency information from the 19 kHz
stereo pilot to recover the 57 kHz RDS/RBDS signal.
5.7.2. Stereo-Mono Blending
Adaptive noise suppression is employed to gradually
combine the stereo left and right audio channels to a
mono (L+R) audio signal as the signal quality degrades
to maintain optimum sound fidelity under varying
reception conditions. Stereo/mono status can be
monitored with the FM_RSQ_STATUS command. Mono
operation can be forced with the
FM_BLEND_MONO_THRESHOLD property.
5.8. De-emphasis
Pre-emphasis and de-emphasis is a technique used by
FM broadcasters to improve the signal-to-noise ratio of
FM receivers by reducing the effects of high-frequency
interference and noise. When the FM signal is
transmitted, a pre-emphasis filter is applied to
accentuate the high audio frequencies. The
Si4736/37/38/39 incorporates a de-emphasis filter
which attenuates high frequencies to restore a flat
frequency response. Two time constants are used in
various regions. The de-emphasis time constant is
programmable to 50 or 75 μs and is set by the
FM_DEEMPHASIS property.
detection, and error correction.
The Si4737/39 device is user configurable and provides
an optional interrupt when RDS is synchronized, loses
synchronization, and/or the user configurable RDS
FIFO threshold has been met.
The Si4737/39 reports RDS decoder synchronization
status and detailed bit errors in the information word for
each RDS block with the FM_RDS_STATUS command.
The range of reportable block errors is 0, 1–2, 3–5, or
6+. More than six errors indicates that the
corresponding block information word contains six or
more non-correctable errors or that the block checkword
contains errors.
*Note: RDS/RBDS is referred to only as RDS throughout the
remainder of this document.
5.12. Tuning
The tuning frequency is directly programmed using the
FM_TUNE_FREQ, WB_TUNE_FREQ, and
AM_TUNE_FREQ commands. The Si4736/37/38/39
supports channel spacing steps of 10 kHz in FM mode,
25 kHz in WB mode, and 1 kHz in AM mode.
Rev. 1.0
23
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
SI4743-C-EVB
BOARD EVALUATION FOR SI4743-C
SI4770-A-EVB
BOARD EVAL FOR CE AM/FM SI4770
SI4777-A20-GM
IC RCVR AM/FM CE HD-RADIO TUNER
SI4804CDY-T1-E3
MOSFET 2N-CH 30V 8A SO8
SI4808DY-T1-GE3
MOSFET N-CH/SCHOTTKY 30V 8SOIC
SI4812BDY-T1-GE3
MOSFET N-CH D-S 30V 8-SOIC
SI4814BDY-T1-GE3
MOSFET N-CH/SCHOTTKY 30V 8SOIC
SI4816DY-T1-GE3
MOSFET N-CH DUAL 30V 8-SOIC
相关代理商/技术参数
Si4738-B20-GM
功能描述:调谐器 Broadcast FM/WB Radio Receiver RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度:
SI4738-B20-GMR
功能描述:IC RX FM/WB RADIO 20UQFN RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘
Si4738-C40-GM
功能描述:射频接收器 BC FM/WB Radio Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4738-C40-GMR
功能描述:射频接收器 Si4738 Broadcast FM/WB Radio Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
Si4738-C40-GU
功能描述:射频接收器 BC FM/WB Radio Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
SI4738-C40-GUR
功能描述:射频接收器 Broadcast FM/WB Radio Receiver RoHS:否 制造商:Skyworks Solutions, Inc. 类型:GPS Receiver 封装 / 箱体:QFN-24 工作频率:4.092 MHz 工作电源电压:3.3 V 封装:Reel
Si4739-B20-GM
功能描述:调谐器 FM/WB Radio Receiver w/ RDS/RBDS RoHS:否 制造商:NXP Semiconductors 功能: 噪声系数: 工作电源电压: 最小工作温度: 最大工作温度:
SI4739-B20-GMR
功能描述:IC RX FM/WB RAD RDS/RBDS 20UQFN RoHS:是 类别:RF/IF 和 RFID >> RF 接收器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS 产品变化通告:Product Discontinuation 09/Jan/2012 标准包装:50 系列:* 频率:850MHz ~ 2.175GHz 灵敏度:- 数据传输率 - 最大:- 调制或协议:- 应用:* 电流 - 接收:* 数据接口:PCB，表面贴装 存储容量:- 天线连接器:PCB，表面贴装 特点:- 电源电压:4.75 V ~ 5.25 V 工作温度:0°C ~ 85°C 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（6x6） 包装:托盘